Known as the most advanced residential macerator in the world, the Saniaccess 3 is one of our top-selling units. A ½ HP pump system, the Saniaccess 3 can install a complete bathroom up to 15 feet below a sewer line, and up to 150 feet from the nearest soil stack. The macerating system is designed to handle human waste, toilet paper, feminine hygiene products, and grey water in a residential setting. The blades of this unit are made from hardened stainless steel, which means they’re durable enough to last for many years to come without replacement or service.

Whether you’re looking for a pump that will allow you to add a bathroom to a basement or what used to be a closet, or simply want to hook a shower, sink, or bathtub up to a durable macerating pump, this option could be the right one for you. Contact our skilled salespeople today to learn more about the benefits of the Saniaccess 3, or to find out how it can fit into your household. We’re always happy to answer any questions you may have and will do what we can to ensure you get the right unit for your purposes.

Type:  Macerating Upflush Toilet

Specifications & Installation Manual:
SaniAccess3 - Official Manual

Product Description:

The SaniACCESS 3 is simplicity itself to install; there are just four connections.

How It Works: Saniflo Instructional Video

Warranty: 2-Year Full Manufacturer Warranty

When the flush is activated, the water flowing into the SaniACCESS 3  activates a micro switch in the pressure chamber, which in turn starts the motor.  The motor is sealed for life in an oil filled enclosure.  A common spindle/shaft drives the impeller and the macerator blades.  The moving parts therefore are kept to an absolute minimum.  Water and organic waste matter enter the chamber and are reduced to slurry as the macerator blades rotate at 3600 RPM.  The centrifugal force causes the reduced solids to be ejected through a grill into the container where it is picked up by the impeller pump mounted beneath the motor.  The unit pumps the effluent upward to 15 feet and/or 150 feet horizontally (with gravity fall).  Once the water level in the container goes down, the micro switch deactivates the unit until the flush is activated again.  A normal operating cycle for SaniACCESS3 takes about 10 - 15 seconds depending upon the discharge pipe run configuration; power consumption is therefore minimal. 

In addition to the toilet waste, the SaniACCESS 3 will also discharge gray water from a variety of other sanitary fixtures such as: a sink, a bathtub, a shower and a urinal.  When adding a bathtub or shower, a base will have to be constructed.  This base should be made out of a 2" x 6" (minimum) or 2" x 8" (recommended) on edge, to allow for the installation of a P-trap and the required 1/4"per foot gravity flow towards the pump unit. 

The waste water from other sanitary fixtures is discharged into the SaniACCESS3  via two 2-inch inlets on either side of the housing.  Either one or both inlets can be used as required.  The discharge elbow on top of the SaniACCESS 3 can be turned either to the left, to the right, or towards the back, depending on the discharge installation.  A non-return valve, which comes already assembled on the discharge elbow, prevents back flow into the unit.

This unit has been designed with a vent connection on the lid.  All plumbing codes require connection to a vent system.  Please note that the vent system should be a two-way air vent.  The use of mechanical vents, air admittance valves or similar devices are not permitted as these are considered one-way air vent systems.  It is also highly recommended for the macerator/pump to be connected to a Ground Fault Interrupter (GFI) circuit.

The SaniACCESS3 unit must be connected to our rear discharge toilet.  This system uses much less water than a regular toilet.

Note: This toilet only works in combination with Saniflo systems.

Plumbing Code Certified: